Automatic Folding Carton Foil Stamper

BRAUSSE 1050SF Automatic Diecutting and Foil Stamping Machine

Feeder

  • Patent turbo spiral air blower pressing foot at feeder head

  • Four pick up and four forward suck heads with angle adjustment

  • Preloading device with rail cart and scaled gate

  • Non – stop feeder with automatic pile lift

  • Left and right side turbo air blower

  • Motorized side adjustment of pallet table

  • Electrical double sheet control

  • Fine air blast at lead edge for smooth thin paper transport

  • Sheet slow down device of feeder belts to assure accurate position of the sheet to the front lays with selective on/off switch

  • Synchronizing device to adjust the sheet positioning to the front lay by hand during production

  • Bullet catcher on the feeder entrance

  • Side lays on both sides push and pull convertible

  • Electronic side lay control to check the sheet position

  • Four individually adjustable front lays with dial read out at the operation side of the machine

  • Two electronic front lay controls by means of Omron Glasfiber optik to control the sheet arrival

  • Photo sensor safety barrier at pallet table floor level touching point

Die cutting Section

  • Precision worm gear crank toggle driving system to ensure smooth and dynamic lower platen movement

  • Precision stationery upper platen

  • Sandwich hardened cutting plate

  • Pneumatic push button diechase locking mechanism to ensure safe and operator friendly changing of the die

  • Pneumatic clutch/brake for main drive system

  • Servo motor drive automatic impression on/off

  • Digital diecutting pressure tonnage display with maximum pressure limit protection

  • Seven high precision alloy gripper bar

  • High quality pre – stretched gripper bar driving chain

  • State – of – art 3 cam index gripper bar driving system to ensure smooth and precise gripper bar intermittent movement

  • Torque limit safety clutch to protect the index driving system in case of gripper bar crash

  • Double cam driven gripper opener and front lay swing frame without position restore spring for smooth and accurate sheet register and take off

  • Air blasting nozzle bar for stretching the thin paper before die cutting

Stripping Section

  • Triple action movement of the upper and lower stripping frames with lower spring loaded stripping pins

  • Motorized upper frame suspending hoister

  • Upper and lower stripping tool mounting frame can be pulled out for job set up and make ready

  • Remote control operation panel for jogging the upper frame up and down, easy and safe stripping tool set up and alignment

  • Quick stripping tool exchange device (optional)

  • Mechanical disconnecting of lower stripping frame when it is not in use

Delivery Section

  • Automatic delivery with non – stop curtain. This curtain moves into the delivery to catch the arriving sheets during the pile exchange

  • Five section brush brake each section angle adjustable individually

  • Air blower to press down the sheets

  • Rare and side joggers with easy position adjustment

  • Tape inserter with counter

  • Safety device to prevent the steel pile plate from clamping on the foot when it reaches at ground level

Specifications hot foil  stamping unit:

Foil advancing shaft:2 (optional 3)
Maximum capacity foil diameter:Ø 200 mm
Foil core diameter:1² or 3²
Maximum foil and stamping size:730 x 1020 mm
Maximum foil stamping speed (subject to paper, foil and stamping die quality as well as operator’s skill)
Foil pull length < 200 mm Foil width ≥ 100 mm
     Foil pull length < 300 mm Foil width ≥ 100 mm
     Foil pull length < 600 mm Foil width = 150 mm
6000 sheets/h
5000 sheets/h 
4000 sheets/h 
Foil pull length 600 - 700 mm Foil width > 150 mm3500 sheets/h
The max. mechanical speed is also 7500 Cycles/H 
Minimum foil width:45mm
Number of heated zones:12
Temperature range:0-200°C
Power for heating:24 KW

Specifications of paper stock range:

Maximum sheet size:1050 x 750 mm
Minimum sheet size:400 x 370 mm
Processable materials
1. Paper (depending on quality), min.:80 – 90 g/m2
2. Carton (depending on quality), up to:600 g/m2
3. Corrugated board (Fine), up to:4 mm
(*) Admissable undulation: 4% of the sheet width
Minimal gripperedge:9.5 mm

Specifications  for diecutting:

Maximum die cutting size:1040 x 720 mm
(Maximum cutting size can be reached at 1040 x 730 mm when the quick locking system is dismantled from the die chase)
Inner size of chase:1145 x 755 mm
Dimensions diecutting plate:1080 x 736 mm
Maximum diecutting pressure:300 T
Maximum mechanical speed:7500 cycles/hour

General specifications:

Power supply for main motor:10 KW.
Power supply for other motors:9 KW.
Total power supply including heating:57KW.
Power voltage:220V 50/60Hz
Pile height feeder, maximum:1530 mm (incl. pallet)
Pile height feeder with Non-Stop operation, maximum:1130 mm (incl. pallet)
Pile height delivery, maximum:1300 mm (incl. pallet)
Pile height over Non-Stop curtain maximum:80 mm
Total length (incl. preloading rails):7016 mm
Total width (incl. catwalk):4049 mm
Total height (incl. raise 200 mm):2167 mm
Total net weight:Approx. 17.5 ton

Contact Us

NO. 1125, TAISHUN RD, ANTING TOWN, JIADING DISTRICT, SHANGHAI, 201814 CHINA

Domestic Sales:
86 21 59502461
International Sales:
86 21 64262538

© 2016 Shanghai Eternal Machinery CO., LTD.

More Inquiries

Didn’t find the information you need?

Please send emails to export@eterna-shanghai.com

aaa