1620 Action Series Automatic Diecutting & Creasing Ma

PE1620S(H)A-Action Automatic Diecutting & Creasing Machine with Stripping Station and Lead Edge Feeder


  • The combination of feeding technology of European diecutting machine and lead edge feeding features of high-speed flexo printing machine, newly designed lead edge feeder with precise feeding system will provide more accurate and positive feeding than ever;

  • High pressure vacuum blower with silencer and AC inverter control volume adjustment, vacuum suction area adjustable according to sheet size;

  • Rear jogger at feeder in preparation for future in line with prefeeder in order to improve productivity and decrease labor cost (Optional);

  • Pneumatic side push guide plates (left and right sides);

  • Left and right hand side guides with separating and synchronizing adjustment available. Inclined front guide plate with back and forth, up and down micro-adjustments to reduce the pressure on bottom sheet of the pile to ensure smooth feeding;

  • Sheet feeding grid height adjustable according to sheet quality and thickness for smooth and precise feeding.


  • Specially designed for diecutting machines, this new worm gear and crank shaft mechanism drives the mobile platen through toggle mechanism more efficiently, reducing the main motor power by 16% and thus decreasing power consumption;

  • Newly designed mobile platen with optimized structural mechanics, more accurate and with minimal deformation under pressure, thus reducing the make ready time;

  • Diecutting station safety door and pneumatic diechase safety locking system;

  • High torque pneumatic clutch/break for positive clutch on and reliable breaking, and special air inlet system to control the air volume for smooth machine start and stop;

  • Air cushion underneath the cutting plate for easy cutting plate in and out;

  • Cutting pressure fine adjustment wheel with position indicate gauge;

  • High quality precision worm gear and toggle system;

  • Newly designed gripper bar driving index unit with large motion angle to allow gripper bar starts and stops gently, thus require less and smaller nicks and higher productivity.  It is also equipped with overloading protection torque limit clutch;

  • High quality, imported pre-stretched gripper bar driving chain;

  • Center line system compatible to Center Line II, makes the cutting die and stripping die centered quickly and precisely;

  • 8 high quality precision alloy gripper bars, each with 12 specially hardened grippers to ensure firm grab of the sheet at high speed;

  • Sheet arrival and departure check photo sensor connected with overall stock monitoring system;

  • Left and right front lay locking blocks with individual adjustments;

  • Chain guide rail use VL compound to improve abrasive resistance and vibration resistance;

  • 10.4’ color touch screen operation panel gives total control of the machine and graphic display machine parameters, job setting, fault diagnosis and etc., more direct and operator friendly;

  • Automatic force lubrication system recycles fluid and is equipped with oil pressure gauge and alarm;

  • Independent main gripper drive chain lubrication;


  • Stationary middle stripping board coupled with special upper stripping frame movement curve in order to produce extra force at waste nipping point for clean waste stripping;

  • Center line system for quick stripping die set up and change over, compatible with Centerline II;

  • Push button of gripper opening is added for easy taking out the production sample at stripping section;

  • Motorized upper stripping frame incerases the operation space, more operator friendly

  • Lead edge waste removal system removes and carries waste edge outside the machine;

  • Full stripping with/without lead edge waste stripping convertible by one button, no tool change, more operator friendly and safe operation;

  • Front edge waste stripping tool with longer stroke and superior curve of motion greatly eases the stripping action;

  • Gravity pull type safety door for easy and safe operator in and out.


  • Escalator delivery fork with non-stop air cylinder for neat and positive delivery and conveyor belt delivery table to protect the sheets from scratches;

  • The bundle delivery table can be prepared for future connection with breaker for in line operation (to be required at order);

  • Electrical batch counter;

  • Spring loaded adjustable chain tension back buffering wheel to maintain the chain tension constantly and smooth gripper bar movements;

  • Mechanical cam driven side joggers and shutter (banana bar), with motorized position adjustment, more accurate and suitable for multi-out diecutting.

Maximum Sheet Size:1620x1200 mm
Minimum Sheet Size:650x450 mm
Maximum Cutting Size:1600x1180 mm
Inner Chase Size:1640x1230 mm
Stock Range:E, B, C, A and AB flute corrugated board
Minimum Gripper Waste(Distance from first knife to paper edge):12 mm (subject to working environment, sheet quality and operation skills, etc.)
Minimum Gripper Margin:6~12 mm
Cutting Rule Height:23.8 mm
Maximum Mechanical Speed:5500 cycles/hour
Production Speed:3500~5000 cycles/hour (subject to working environment, sheet quality and operation skills, etc.)
Maximum Cutting Pressure:400 tons
Total Power Required:38 KW
Main Motor Power:18.5 KW
Electrical Power:380V, 50HZ, 3-phase
Air Pump Displacement:1.05m³/min, 12kg/cm2 (Prepared by User)
Mobile Lower Platen Adjusting Range:±1.5 mm
Net Weight of Machine:
Gross Weight of Machine:
Machine Dimensions:10960(L)x5820(W)x2514(H) mm (incl. Catwalk)

Contact Us


Domestic Sales:
86 21 59502461
International Sales:
86 21 64262538

© 2016 Shanghai Eternal Machinery CO., LTD.

More Inquiries

Didn’t find the information you need?

Please send emails to export@eterna-shanghai.com